Today's reality dictates an increasingly daunting task. To meet the latest ANSI ESD static control standards and assure your successful manufacturing of static sensitive electronics esd flooring is a must! Yet in today's economy does it make since to pay $7.00 to 10.00 per installed square foot for esd tiles, thick set esd epoxy or an anti-static rubber floor? Most think NOT! ElectraSeal seals concrete with an effective static control formulation designed to meet today's latest requirements for static control flooring and eliminate dust production of the concrete slab for less than $.20 cents per square foot!
Application: Best results are obtained when ElectraSeal is applied to cured concrete surfaces which are 60 Deg F. or warmer and in relative humidity conditions of < 50%. Thoroughly vacuum slab to remove any loose dirt or dust. If contaminants such as oil and grease have soaked into the slab wash with ElectraClean rinse slab and allow to dry completely prior to application of ElectraSeal. Three coats will provide the optimum gloss and durability. Apply thin even coats using new loop end rayon or other non linting finish mops, allowing ElectraSeal to dry, (depending on humidity and temperature) for approximately 60 minutes between coats. Typical life span of product is at least 3 years. ElectraSeal may be effectively recoated without removal. For best results do not burnish. If a higher luster is required top coat this material with one thin coat of ElectraGlaze floor finish prior to high speed polishing.
Maintenance: ElectraSeal is an extremely durable Anti Static concrete sealer. After application and curing of ElectraSeal routine maintenance (to be expected with any floor) is all that is required to maintain the luster and conductivity of the finish. It's important to remove abrasives that can scratch and degrade the conductivity by dry mopping (usually on a daily basis). On an occasional basis (most of our clients prefer to do this once every week or two) damp mop the floor with a diluted mixture of ElectraClean and water and allow to dry. Note: Use only ElectraClean to damp mop your ElectraSeal floor,NEVER wash any esd floor with plain water. ElectraSeal does not readily lend itself to high speed polishing or burnishing. If a high speed polishing (produces ultimate shine) is desirable top coat the ElectraSeal with a single coat of ElectraGlaze prior to polishing.
ELECTRASEAL ANTI STATIC ESD CONTROL CONCRETE SEALER!
Today's reality dictates an increasingly daunting task. To meet the latest ANSI ESD static control standards and assure your successful manufacturing of static sensitive electronics esd flooring is a must! Yet in today's economy does it make since to pay $7.00 to 10.00 per installed square foot for esd tiles, thick set esd epoxy or an anti-static rubber floor? Most think NOT! ElectraSeal seals concrete with an effective static control formulation designed to meet today's latest requirement and eliminate dust production of the concrete slab for less than $.20 cents per square foot!
WHY A STATIC CONTROL CONCRETE SEALER?
APPLICATION IS FAST, EASY AND LOW ODOR!Best results are obtained when ElectraSeal is applied to cured concrete surfaces which are 60 Deg F. or warmer and in relative humidity conditions of < 50%. Thoroughly vacuum slab to remove any loose dirt or dust. If contaminants such as oil and grease have soaked into the slab wash with ElectraClean, rinse slab and allow to dry completely prior to application of ElectraSeal. Three coats will provide the optimum gloss and durability. Apply thin even coats using new loop end rayon or other non linting finish mops, allowing ElectraSeal to dry, (depending on humidity and temperature) for approximately 60 minutes between coats. Typical life span of product is at least 3 years. ElectraSeal may be effectively recoated without removal. For best results do not burnish. If a higher luster is required top coat this material with one thin coat of ElectraGlaze prior to high speed polishing.
EASY TO MAINTAIN!
ElectraSeal is an extremely durable Anti Static concrete sealer. After application and curing of ElectraSeal routine maintenance (to be expected with any floor) is all that is required to maintain the luster and conductivity of the finish. It's important to remove abrasives that can scratch and degrade the conductivity by dry mopping (usually on a daily basis). On an occasional basis (most of our clients prefer to do this once every week or two) damp mop the floor with a diluted mixture of ElectraClean and water and allow to dry. Note: Use only ElectraClean to damp mop your ElectraSeal floor,NEVER wash any esd floor with plain water. ElectraSeal does not readily lend itself to high speed polishing or burnishing. If a high speed polishing (produces ultimate shine) is desirable top coat the ElectraSeal with a single coat of ElectraGlaze prior to polishing.
