ElectraGlaze Quart Sample

Static Control Equipment

ESD Flooring & Floor Care

Static Control for Offices

Sample Request

All Samples

Home > All Samples >

E-Glaze Quart Sample

ElectraGlaze Quart Sample

Our Price: $15.00

Availability: Usually Ships in 24 Hours
Product Code: E-GLAZE QUART SAMPLE

Qty:

Description

Technical Specs and Downloads

This quart sample of ElectraGlaze antistatic floor finish is for use on esd tiles and static conductive ESD epoxy. This product is high shine, easy to apply, and can be recoated without stripping. Our ElectraGlaze is long lasting and helps control electrostatic discharge. For more information on ElectraGlaze please click here!

MSDS SHEET

SDS Sheet (download)

Electrostatic Decay Time EIA 541: <0.2 sec

Product Data:

% solids: >20%

ASTM D2834-34

pH: 7.25

Shelf Life: 18 months min

Flash Point: none

ASTM E70-77

Gloss: 88 min

ASTM D1455-82

Recoatability: Excellent

ASTM D3153-78 Rubber Heel Marks: 1.0

ASTM D1436-82/ Resistance: Excellent

CSMA # 9-73 Powdering Resistance: Excellent

ASTM D2048-82 Freeze / Thaw Stability: Passes 3 Cycles

ASTM D3209-82 Static coefficient of friction: >0.55

ASTM D2047-82 Slip Resistance per NFSI test method 101-A: 0.7 Neolite, 0.8 rubber

Application: ESD floor finish is not applied "just like" standard floor finish, take the time to understand the differences! It will save you time in the long run. This material is for use on ESD vinyl, epoxy and standard hard surface flooring. If the floor has been previously coated with a wax or "factory applied finish" (as is the case with standard VCT, OR if floor is extremely dirty, remove contaminants with emulsifying floor stripper such as ElectraStrip Floor Stripping Liquid. Power Scrub with pad, double rinse with clean water. Allow to dry thoroughly. Using a clean Rayon mop or wax applicator, apply thin even coats of ElectraGlaze allowing finish to dry 2 hours between coats. Two coats are recommended for optimum performance on ESD Floors, up to 5 coats are recommended for non esd floors. Buffing is not required between coats unless high luster is desired. Note: Avoid application during high humidity conditions.

Maintenance: Dry mop floors with an untreated mop daily to remove loose dirt, sand and other abrasives. As needed: damp mop using ElectraClean ESD Flooring Cleaner ONLY diluted 10:1 to remove soils which can degrade the coatings conductive properties and gloss. Heavily soiled areas and scuff marks can be removed by spray buffing with ElectraShine. NOTE: Do not use plain water (without the addition of ElectraClean) to damp mop your floor. Do not apply diluted ElectraClean for 48 hours after initial application of ElectraGlaze. If a high shine is required high speed polish with finest pad possible using coarser pads only as needed. For best results consider the use of a propane powered high speed polishing machine.

Features

Long lasting, easy to apply!
Reduces maintenance cost.
Non flaking, perfect for sensitive electronics!
Lowers tribo-charge generation.
Meets UL slip resistance standards.
Makes scuff marks EASY to remove!
Pleasant low odor, no VOC's!
Biodegradable, environmentally oriented!
Perfect for any hard surface ESD floor. THE recommended sealer for ElectraGuard ESD Epoxy Paint!

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

All Samples
All Samples > Paints and Chemical Samples

United Static Control Products, Inc

Static Control Equipment

ESD Flooring & Floor Care

Static Control for Offices

Sample Request