United Static Control Products, Inc

• MSDS SHEET
• Electrostatic Decay Time EIA 541: <0.2 sec
• Product Data:
• % solids: >20%
• ASTM D2834-34
• pH: 7.25
• Shelf Life: 18 months min
• Flash Point: none
• ASTM E70-77
• Gloss: 88 min
• ASTM D1455-82
• Recoatability: Excellent
• ASTM D3153-78 Rubber Heel Marks: 1.0
• ASTM D1436-82/ Resistance: Excellent
• CSMA # 9-73 Powdering Resistance: Excellent
• ASTM D2048-82 Freeze / Thaw Stability: Passes 3 Cycles
• ASTM D3209-82 Static coefficient of friction: >0.55
• ASTM D2047-82 Slip Resistance per NFSI test method 101-A: 0.7 Neolite, 0.8 rubber
• Application: ESD floor finish is not applied "just like" standard floor finish, take the time to understand the differences! It will save you time in the long run. This material is for use on ESD vinyl, epoxy and standard hard surface flooring. If the floor has been previously coated with a wax or "factory applied finish" (as is the case with standard VCT, OR if floor is extremely dirty, remove contaminants with emulsifying floor stripper such as ElectraStrip Floor Stripping Liquid. Power Scrub with pad, double rinse with clean water. Allow to dry thoroughly.  Using a clean Rayon mop or wax applicator, apply thin even coats of ElectraGlaze allowing finish to dry 2 hours between coats.  Two  coats are recommended for optimum performance on ESD Floors, up to 5 coats are recommended for non esd floors. Buffing is not required between coats unless high luster is desired. Note: Avoid application during high humidity conditions.
• Maintenance: Dry mop floors with an untreated mop daily to remove loose dirt, sand and other abrasives.  As needed: damp mop using ElectraClean ESD Flooring Cleaner ONLY diluted 10:1 to remove soils which can degrade the coatings conductive properties and gloss. Heavily soiled areas and scuff marks can be removed by spray buffing with ElectraShine.  NOTE: Do not use plain water (without the addition of ElectraClean) to damp mop your floor. Do not apply diluted ElectraClean for 48 hours after initial application of ElectraGlaze. If a high shine is required high speed polish with finest pad possible using coarser pads only as needed. For best results consider the use of a propane powered high speed polishing machine.

ElectraGlaze and our refined system of static control floor care products = Ultimate Performance, Conductivity and Longevity. ElectraGlaze Shine and Scuff removal?  Outstanding PERIOD. If you're like most of our clients you've grown weary of seeing your resistance values rise to the point that you're hoping for a rainy day to bring them down!

NO MORE WISHFUL THINKING OR PRAYING FOR RAIN!

When used in conjunction with static conductive esd flooring ElectraGlaze provides superior shine, slip, wear and scuff resistance. 2 thin costs slightly raise the insulative properties of the flooring but the reduction in maintenance cost is well worth the modest sacrifice in conductivity. 2 thin coats applied to a static conductive vinyl or epoxy do not typically exceed the new ANSI / ESD recommended electrical resistance limits of >3.5E07 per ESD 97.1 testing. When used on Standard (non esd floors) 5 thin coats will typically bring the electrical resistance to <1.0E09 @ 50% relative humidity. This range of electrical conductivity does not meet the new ANSI/ESD S20.20-2007 criteria for performance but is useful for reduction of nuisance static and for meeting the older ESD S20.20 protocol.