ElectraEtch Biodegradable Concrete Etch

Home > ElectraGuard Static Control Floor Paint > Concrete Etching Solutions >

ElectraEtch Acid Etching Solution

Biodegradable Concrete Etch for preparation of esd flooring materials

ElectraEtch is a concentrated formulation containing Hydrochloric (muriatic) Acid, detergents and surfactants. It's designed specifically for use with ElectraGuard esd floor paint, ElectraSeal low voc "Green" esd concrete sealer and ElectraTile's LG-5100 esd tile adhesive on an "as needed" basis.

NOTE: ElectraEtch can not be shipped expedited (air freight). Please take the time to read and UNDERSTAND the MSDS Sheet.

Our Price: $11.99

Product Code: ELECTRAETCH-QT

Qty:

Description

Technical Specs and Downloads

Extended Information

ElectraEtch is a concentrated formulation containing Hydrochloric (muriatic) Acid, detergents and surfactants. It's designed specifically or use with ElectraGuard esd floor paint, ElectraSeal low voc "Green" esd concrete sealer and ElectraTile's LG-5100 esd tile adhesive. ElectraEtch is for use in preparing concrete, terrazzo and unglazed ceramic or stone. ElectraEtch's powerful chemical reaction dissolves ground in dirt and dust opening up the pores in smooth mineral surfaces insuring the proper profile for a successful application or our ESD flooring material.

SDS SHEET

Click HERE for Material Safety Data Sheet

CAUTION: This is a concentrated product formulated for professional use only! Safety glasses, gloves and protective footwear should be worn at all times during application. Provide for adequate ventilation of fumes which may be generated during the application. In enclosed areas with limited ventilation a respirator may be necessary. DO NOT mix this product with other chemicals. NOTE: ElectraEtch should be used with extreme caution on polished surfaces and marble, terrazzo, limestone, or other calcium containing materials. ElectraEtch will remove the gloss from polished surfaces and will etch and possibly damage soft or high calcium content stones. APPLICATION: Uniformly dampen the area to be treated with clean water. For light to medium soil or staining on ceramic tile of stone dilute ElectraEtch 1 part product to 3 parts cold water. For heavy soil or staining or for etching concrete ElectraEtch may be concentrated 1 part product to 1 part cold water. NOTE: Concentrations of ElectraEtch at 1:1 or higher can cause efflorescence in grout lines which should be removed by scrubbing with hot water and a deck brush or a 175-300 RPM buffing machine equipped with a brush. Apply solution to the floor using a plastic watering can then spread EVENLY using a synthetic fiber deck brush or synthetic fiber mop. Allow the solution to work for approximately 5 minutes or until the white foaming action ceases. NOTE: Do Not allow the product to pool or puddle as over etching may occur and shadow thru the subsequent coating of ElectraGuard ESD Epoxy Floor Paint or ElectraSeal concrete sealer. Scrub the application area with a buffing machine equipped with a staggered bristle zim-grit or nylo-grit type brush or deck brush to assist in thorough cleaning. Completely remove the etching solution, preferably with a wet vacuum. Rinse by applying clean water liberally with a watering can or mop. Scrub briefly to agitate rinse water. Remove rinse water with a wet vac or mop. Thoroughly rinse all application equipment with clean water. COVERAGE: Approximately 250 square feet per gallon of diluted solution.

Features

Bio-degradable yet highly effective.
Dissolves the most STUBBORN of dirt.
Concentrated, adjustable strength!
Dependable results!

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

ElectraGuard Static Control Floor Paint > Concrete Etching Solutions

	ElectraGuard Installation Tools- Small ElectraGuard Paint Agitator $9.99